油水分離器是什么？工作原理有什么？

發布人：http://   發布時間：2018-05-22 15:28:33

    無動力油水分離器是什么？
    What is an unpowered oil-water separator?
    無動力油水分離器是由預過濾器、聚結分離器、吸附過濾器、泵體、控制箱、車體組成的一種水中除油的過濾設備。無動力油水分離器可處理含油量在5000mg/L的所有的工業上用的輕質油類，簡單的說就是在水多油少的情況下，要使用無動力油水分離器來進行油和水的分離。
    An unpowered oil-water separator is a filter equipment consisting of a pre filter, a coalescer, an adsorption filter, a pump body, a control box, and a car body. The unpowered oil-water separator can handle all the light oil used in the industry of 5000mg/L, which is simply to use the unpowered oil-water separator to separate the oil and water in the case of less water.
    無動力油水分離器工作過程？
    The working process of the unpowered oil-water separator?
    1、啟動泵源開關，依次打開預過濾器、聚結過濾器上的排氣閥，待排氣閥有水溢出時，表明該腔體內已充滿水，此時關閉該排氣閥，待各腔體均充滿水時，打開出水球閥。也可以通過電磁閥手動排氣，排氣過程一般只需在在設備剛開始工作時進行，設備正常運行后不需排氣。根據出水水質情況，可以通過出水閥適當調節進水流量的大小，出水水質差可減小流量，反之可增大流量。

    start the pump source switch, turn on the exhaust valve on the pre filter and the coalescence filter in turn. When the exhaust valve has water overflow, it shows that the cavity is filled with water. At this time, the exhaust valve is closed and the water ball valve is opened when all the cavities are filled with water. It can also be manually exhausting through the solenoid valve. The exhaust process is usually carried out at the beginning of the operation of the equipment, and no exhaust is required after normal operation of the equipment. According to the effluent quality, the influent flow can be properly adjusted through the outlet valve. The poor water quality can reduce the flow rate, otherwise the flow rate can be increased.
    2、清水從出水口排出，集油室開始集油，油水界面開始下降。當油浸沒住傳感器的電極棒時，傳感器輸出信號，電磁閥處于開通狀態，排油電磁閥開始排油，此時相應的電磁閥指示燈亮，當排油控制箱設定的延時時間到時，排油電磁閥關閉，排油指示燈熄滅，排油結束。排油后，油水界面開始上升，電極棒處于水中時，傳感器停止輸出信號，從觀察窗上可以觀察油位高低。
    The water is discharged from the outlet, and the oil gathering room begins to collect oil, and the oil-water interface begins to decline. When the oil impregnated with the electrode rod of the sensor, the sensor output signal, the solenoid valve is in the open state, the oil discharge electromagnetic valve starts to drain. At this time the corresponding electromagnetic valve indicator light is bright. When the delay time of the oil control box is set, the oil discharge electromagnetic valve is closed, the oil discharge indicator is extinguished and the oil discharge is finished. After the oil discharge, the oil water interface starts to rise. When the electrode bar is in the water, the sensor stops the output signal, and the oil level can be observed from the observation window.
    3、每次停機前應將清水注滿水油分離器各腔體并關閉進、出水球閥。若長時間停機不用，應在停機前以清水運行20分鐘，直存油全部從油水分離器內腔排出。
    finally, every time before stopping, fill the water and oil separator with water and close the inlet and outlet ball valves. If there is no need to stop for a long time, clear the water for 20 minutes before stopping, until the oil is discharged from the inner cavity of the oil-water separator.